Difference between revisions of "RFM12 FS20"
| Line 35: | Line 35: | ||
the [http://jeelabs.net/projects/cafe/wiki/Receiving_OOKASK_with_a_modified_RFM12B C_arssi capacitor needs to be replaced] | the [http://jeelabs.net/projects/cafe/wiki/Receiving_OOKASK_with_a_modified_RFM12B C_arssi capacitor needs to be replaced] | ||
with a value 150 pf. | with a value 150 pf. | ||
| − | |||
| − | |||
The SPI connection is pretty fixed and does not need special pinnings. For the chip select (CS) of | The SPI connection is pretty fixed and does not need special pinnings. For the chip select (CS) of | ||
| Line 52: | Line 50: | ||
If more than one RFM12 are used with Ethersex, the number in SPI_CS_RFM12_0 defines the number of the module. | If more than one RFM12 are used with Ethersex, the number in SPI_CS_RFM12_0 defines the number of the module. | ||
Each needs its own pinning. The RFM12_USE_INT defines whether FSK/DATA/nFSS is connected to INT0, INT1 or INT2 of the ATmega. | Each needs its own pinning. The RFM12_USE_INT defines whether FSK/DATA/nFSS is connected to INT0, INT1 or INT2 of the ATmega. | ||
| + | |||
| + | == Configuration == | ||
[[Category:RFM12]] | [[Category:RFM12]] | ||
Revision as of 10:40, 11 March 2013
| RFM12 FS20 | |
|---|---|
| Status | In Development
|
| menuconfig | I/O->RFM12 ASK->868MHz |
| Pinning | yes |
| Ecmd | yes |
| Control6 | no |
| Depends on | ECMD RFM12 ASK |
| Requires | - |
| Code | https://github.com/ethersex/ethersex/tree/master/hardware/radio/rfm12 |
The FS20 / FHT system by ELV is currently the most successful wireless home control system in the low cost sector. This arises from the large number of components and the continuous expansion of the system. But the relatively low price, the comprehensive home control systems far below the price of such EIB systems permits, plays a crucial role.
This FS20 modul is based on CULFW by Rudolf Koenig and supports a wide range of protocols:
- FS20: send/receive
There are numerous FS20 devices, all of them are fully supported. - FHT: send/receive
Communication to the FHT80b is supported. - S300: receive
Examples of such devices: S300TH, KS300-2 - EM1000: receive
Devices: EM1000FM, EM1000GZ, EM1000WZ - HMS: receive
Devices: There are numerous HMS devices, all of them are fully supported. - ESA2000: receive
- Lacrosse TX2/TX3: receive
Connection
The RFM12 is connected to the ATmegalike in FSK Mode with a small difference. The output FSK/DATA/nFSS signal (Pin 3) is connected to one of the INT pins of the ATmega.
The software uses the digital filter of the RFM12. To improve sensitivity on short and long distances the C_arssi capacitor needs to be replaced with a value 150 pf.
The SPI connection is pretty fixed and does not need special pinnings. For the chip select (CS) of the modul and the optional LEDs the pinning must be defined.
/* port the rfm12 module CS is attached to */ pin(SPI_CS_RFM12_0, PB0, OUTPUT) /* port the LEDS for rfm12 tx/rx attached to */ pin(STATUSLED_RFM12_TX, PB3, OUTPUT) pin(STATUSLED_RFM12_RX, PB1, OUTPUT) RFM12_FS20_USE_INT(1)
If more than one RFM12 are used with Ethersex, the number in SPI_CS_RFM12_0 defines the number of the module. Each needs its own pinning. The RFM12_USE_INT defines whether FSK/DATA/nFSS is connected to INT0, INT1 or INT2 of the ATmega.
