Difference between revisions of "ECMD Reference"
m |
m |
||
| Line 3: | Line 3: | ||
repository. Do not edit this page but send [[patches]] for those files! | repository. Do not edit this page but send [[patches]] for those files! | ||
</div> | </div> | ||
| − | |||
| − | |||
| − | |||
__NOTOC__ | __NOTOC__ | ||
| − | + | == Bluetooth SPP Module ([[Bluetooth]]) == | |
| − | + | {| border='1' | |
| − | + | | ''Command syntax'' | |
| − | + | | ''Short description'' | |
| + | |- | ||
| + | | bt cmd | ||
| + | | send an AT command | ||
| + | |- | ||
| + | | bt stats | ||
| + | | report statistics counter | ||
| + | |- | ||
| + | |} | ||
== DNS Resolver == | == DNS Resolver == | ||
{| border='1' | {| border='1' | ||
| Line 30: | Line 35: | ||
|- | |- | ||
| ltc1257_delay `[VALUE] | | ltc1257_delay `[VALUE] | ||
| − | | Set (if VALUE given) or get (no VALUE) delay for LTC1257 output bit changes in | + | | Set (if VALUE given) or get (no VALUE) delay for LTC1257 output bit changes in µs' |
|- | |- | ||
| ltc1257_set `[VALUE0] [VALUE1] ... | | ltc1257_set `[VALUE0] [VALUE1] ... | ||
| Line 47: | Line 52: | ||
| GREEN,BLUE",fnordlicht command to set RGB color | | GREEN,BLUE",fnordlicht command to set RGB color | ||
|- | |- | ||
| − | | fnordlicht_init | + | | fnordlicht_init |
| fnordlicht init | | fnordlicht init | ||
|- | |- | ||
| Line 73: | Line 78: | ||
| lcd goto LINE COL | | lcd goto LINE COL | ||
| Move cursor to LINE and column COL (origin is 0/0) | | Move cursor to LINE and column COL (origin is 0/0) | ||
| + | |- | ||
| + | | lcd print charset FROM TO | ||
| + | | Print char FROM up to char TO | ||
|- | |- | ||
| lcd reinit CURSOR BLINK | | lcd reinit CURSOR BLINK | ||
| Line 89: | Line 97: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | irmp receive | + | | irmp receive |
| receive an IR command | | receive an IR command | ||
|- | |- | ||
| Line 101: | Line 109: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | ir receive | + | | ir receive |
| receive an IR command | | receive an IR command | ||
|- | |- | ||
| Line 116: | Line 124: | ||
| Adjust periodic timers TOP value by adding OFFSET ticks. | | Adjust periodic timers TOP value by adding OFFSET ticks. | ||
|- | |- | ||
| − | | periodic reset | + | | periodic reset |
| Reset debug statistics for periodic module. | | Reset debug statistics for periodic module. | ||
|- | |- | ||
| − | | periodic stats | + | | periodic stats |
| Print debug statistics for periodic module. | | Print debug statistics for periodic module. | ||
|- | |- | ||
| Line 128: | Line 136: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | ntp query | + | | ntp query |
| Query the NTP server to get an NTP update. | | Query the NTP server to get an NTP update. | ||
|- | |- | ||
| Line 134: | Line 142: | ||
| Display/Set the IP address of the NTP server to use to IPADDR. | | Display/Set the IP address of the NTP server to use to IPADDR. | ||
|- | |- | ||
| − | | ntp status | + | | ntp status |
| Display NTP server status | | Display NTP server status | ||
|- | |- | ||
| Line 143: | Line 151: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | enc dump | + | | enc dump |
| Dump the internal state of the enc to serial | | Dump the internal state of the enc to serial | ||
|- | |- | ||
| Line 194: | Line 202: | ||
| Write Hexbytes at address after the config in epprom. | | Write Hexbytes at address after the config in epprom. | ||
|- | |- | ||
| − | | hostname | + | | hostname |
| Display hostname. | | Display hostname. | ||
|- | |- | ||
| Line 203: | Line 211: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | bootloader | + | | bootloader |
| Call the bootloader. | | Call the bootloader. | ||
|- | |- | ||
| − | | reset | + | | reset |
| Reset the Ethersex. | | Reset the Ethersex. | ||
|- | |- | ||
| − | | wdreset | + | | wdreset |
| Go into endless loop to trigger a watchdog timeout. | | Go into endless loop to trigger a watchdog timeout. | ||
|- | |- | ||
| Line 218: | Line 226: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | ads get | + | | ads get |
| Get the ADC value in hex. | | Get the ADC value in hex. | ||
|- | |- | ||
| Line 224: | Line 232: | ||
| Get the mean of power of 2 COUNT ADC values in hex. | | Get the mean of power of 2 COUNT ADC values in hex. | ||
|- | |- | ||
| − | | fuse | + | | fuse |
| Display current fuse settings | | Display current fuse settings | ||
|- | |- | ||
| Line 234: | Line 242: | ||
|- | |- | ||
| ask 1527 HOUSECODE COMMAND DELAY CNT | | ask 1527 HOUSECODE COMMAND DELAY CNT | ||
| − | | | + | | |
|- | |- | ||
| ask 2272 HOUSECODE COMMAND [DELAY] [CNT] [SYNC] | | ask 2272 HOUSECODE COMMAND [DELAY] [CNT] [SYNC] | ||
| − | | | + | | |
|- | |- | ||
| ask fa20rf DEVICE [REPEAT] | | ask fa20rf DEVICE [REPEAT] | ||
| − | | | + | | |
|- | |- | ||
| ask intertechno FAMILY GROUP DEVICE COMMAND | | ask intertechno FAMILY GROUP DEVICE COMMAND | ||
| "Send Command to Intertechno switches (with coding wheel). FAMILY: A=1, ..." | | "Send Command to Intertechno switches (with coding wheel). FAMILY: A=1, ..." | ||
|- | |- | ||
| − | | ask itsl HOUSECODE COMMAND BUTTON [DIM] | + | | ask itsl HOUSECODE COMMAND BUTTON [DIM] |
| "Send Command to Intertechno Self learning switches and dimmers. DIM works only with dimmers and values 0-15." | | "Send Command to Intertechno Self learning switches and dimmers. DIM works only with dimmers and values 0-15." | ||
|- | |- | ||
| ask oase FAMILY GROUP DEVICE COMMAND | | ask oase FAMILY GROUP DEVICE COMMAND | ||
| − | | | + | | |
|- | |- | ||
| ask tevion HOUSECODE COMMAND DELAY CNT | | ask tevion HOUSECODE COMMAND DELAY CNT | ||
| − | | | + | | |
|- | |- | ||
|} | |} | ||
| Line 260: | Line 268: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | date | + | | date |
| Print the current date. | | Print the current date. | ||
|- | |- | ||
| − | | lastdcf | + | | lastdcf |
| Print when last valid DCF signal was received. | | Print when last valid DCF signal was received. | ||
|- | |- | ||
| Line 269: | Line 277: | ||
| Display/Set the current time in seconds since January 1st 1970. | | Display/Set the current time in seconds since January 1st 1970. | ||
|- | |- | ||
| − | | uptime | + | | uptime |
| Display ethersex uptime in unix format. | | Display ethersex uptime in unix format. | ||
|- | |- | ||
| − | | whm | + | | whm |
| Display ethersex uptime. | | Display ethersex uptime. | ||
|- | |- | ||
| Line 281: | Line 289: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | sample | + | | sample |
| Manually call application sample commands | | Manually call application sample commands | ||
|- | |- | ||
| − | | sample_init | + | | sample_init |
| Manually call application sample init method | | Manually call application sample init method | ||
|- | |- | ||
| − | | sample_periodic | + | | sample_periodic |
| Manually call application sample periodic method | | Manually call application sample periodic method | ||
|- | |- | ||
| Line 299: | Line 307: | ||
| Show specific message currently in buffer format value as TYPE type is one of RAW STA TMP FP1 FP5 | | Show specific message currently in buffer format value as TYPE type is one of RAW STA TMP FP1 FP5 | ||
|- | |- | ||
| − | | bsbport list | + | | bsbport list |
| List all messages currently in buffer output in RAW TMP FP1 FP5 | | List all messages currently in buffer output in RAW TMP FP1 FP5 | ||
|- | |- | ||
| bsbport query P1 P2 P3 P4 [DEST] | | bsbport query P1 P2 P3 P4 [DEST] | ||
| − | | Send Message to query for a value DEST is optional defaults to 0 | + | | Send Message to query for a value DEST is optional defaults to 0 |
|- | |- | ||
| bsbport set P1 P2 P3 P4 DEST TYPE VALUE | | bsbport set P1 P2 P3 P4 DEST TYPE VALUE | ||
| Send Message to set value type is one of RAW SEL TMP FP1 FP5 | | Send Message to set value type is one of RAW SEL TMP FP1 FP5 | ||
|- | |- | ||
| − | | bsbport stats | + | | bsbport stats |
| Report statistic counters OK/CRC/Lenght under/Lenght over/Droped/Buffer/BufferNet/Retransmit | | Report statistic counters OK/CRC/Lenght under/Lenght over/Droped/Buffer/BufferNet/Retransmit | ||
|- | |- | ||
| Line 320: | Line 328: | ||
| Select module N | | Select module N | ||
|- | |- | ||
| − | | mcuf modul list | + | | mcuf modul list |
| List all modules | | List all modules | ||
|- | |- | ||
| − | | mcuf showclock | + | | mcuf showclock |
| Show digital clock | | Show digital clock | ||
|- | |- | ||
| Line 344: | Line 352: | ||
| Get/Set ADC reference voltage calibration. | | Get/Set ADC reference voltage calibration. | ||
|- | |- | ||
| − | | crc calc | + | | crc calc |
| "read the ethersex program code and calc a crc16 of it" | | "read the ethersex program code and calc a crc16 of it" | ||
|- | |- | ||
| − | | crc read | + | | crc read |
| "read out the crc16 value at the end of the program space" | | "read out the crc16 value at the end of the program space" | ||
|- | |- | ||
| − | | hr20 temp | + | | hr20 temp |
| Read HR20 temperature sensor. | | Read HR20 temperature sensor. | ||
|- | |- | ||
| Line 365: | Line 373: | ||
| show/set job anacron state | | show/set job anacron state | ||
|- | |- | ||
| − | | cron list | + | | cron list |
| Show all cron entries | | Show all cron entries | ||
|- | |- | ||
| Line 374: | Line 382: | ||
| Remove one cron entry | | Remove one cron entry | ||
|- | |- | ||
| − | | cron save | + | | cron save |
| Saves all persistent jobs | | Saves all persistent jobs | ||
|- | |- | ||
| Line 407: | Line 415: | ||
| Return humidity of DHT sensor | | Return humidity of DHT sensor | ||
|- | |- | ||
| − | | dht list | + | | dht list |
| Return a list of mapped sensor names | | Return a list of mapped sensor names | ||
|- | |- | ||
| Line 419: | Line 427: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | dmx fxslot devices | + | | dmx fxslot devices |
| set the device settings | | set the device settings | ||
|- | |- | ||
| − | | dmx fxslot effect | + | | dmx fxslot effect |
| set the effect settings | | set the effect settings | ||
|- | |- | ||
| − | | dmx fxslot reset | + | | dmx fxslot reset |
| reset all fxslots and clear saved ones in EEPROM | | reset all fxslots and clear saved ones in EEPROM | ||
|- | |- | ||
| − | | dmx fxslot restore | + | | dmx fxslot restore |
| restore the settings from EEPROM | | restore the settings from EEPROM | ||
|- | |- | ||
| − | | dmx fxslot save | + | | dmx fxslot save |
| save the current fxslots to EEPROM | | save the current fxslots to EEPROM | ||
|- | |- | ||
| Line 440: | Line 448: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | dmx channels | + | | dmx channels |
| Get channels per universe | | Get channels per universe | ||
|- | |- | ||
| − | | dmx get | + | | dmx get |
| Return channel value | | Return channel value | ||
|- | |- | ||
| − | | dmx set | + | | dmx set |
| Set channel values | | Set channel values | ||
|- | |- | ||
| − | | dmx universe | + | | dmx universe |
| Get a whole universe | | Get a whole universe | ||
|- | |- | ||
| − | | dmx universes | + | | dmx universes |
| Get universes | | Get universes | ||
|- | |- | ||
| Line 460: | Line 468: | ||
| ''Command syntax'' | | ''Command syntax'' | ||
| ''Short description'' | | ''Short description'' | ||
| − | |||
| − | |||
| − | |||
|- | |- | ||
| 1w ds2450 convert [DEVICE] | | 1w ds2450 convert [DEVICE] | ||
| Line 491: | Line 496: | ||
| Return temperature value of onewire device (provide 64-bit ID as 16-hex-digits) | | Return temperature value of onewire device (provide 64-bit ID as 16-hex-digits) | ||
|- | |- | ||
| − | | 1w list | + | | 1w list |
| Return a list of the connected onewire devices | | Return a list of the connected onewire devices | ||
|- | |- | ||
| Line 497: | Line 502: | ||
| Delete a name mapping | | Delete a name mapping | ||
|- | |- | ||
| − | | 1w name list | + | | 1w name list |
| Return a list of mapped device names | | Return a list of mapped device names | ||
|- | |- | ||
| − | | 1w name save | + | | 1w name save |
| Save name mappings to EEPROM | | Save name mappings to EEPROM | ||
|- | |- | ||
| Line 512: | Line 517: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | df status | + | | df status |
| Display internal status. | | Display internal status. | ||
|- | |- | ||
| − | | fs format | + | | fs format |
| Format the filesystem. | | Format the filesystem. | ||
|- | |- | ||
| Line 524: | Line 529: | ||
| Inspect NODE and dump to serial. | | Inspect NODE and dump to serial. | ||
|- | |- | ||
| − | | fs list | + | | fs list |
| List the directory. | | List the directory. | ||
|- | |- | ||
| Line 542: | Line 547: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | dc3840 capture | + | | dc3840 capture |
| Take a picture. Access 'dc3840' via VFS afterwards. See [[DC3840 Camera]] for details. | | Take a picture. Access 'dc3840' via VFS afterwards. See [[DC3840 Camera]] for details. | ||
|- | |- | ||
| − | | dc3840 light | + | | dc3840 light |
| Light level of camera | | Light level of camera | ||
|- | |- | ||
| Line 551: | Line 556: | ||
| Send provided command bytes to the camera. | | Send provided command bytes to the camera. | ||
|- | |- | ||
| − | | dc3840 sync | + | | dc3840 sync |
| Re-sync to the camera | | Re-sync to the camera | ||
|- | |- | ||
| − | | dc3840 zoom | + | | dc3840 zoom |
| Enable zoom of camera | | Enable zoom of camera | ||
|- | |- | ||
| Line 570: | Line 575: | ||
|- | |- | ||
| dec VAR | | dec VAR | ||
| − | | Decrement variable VAR (a number) | + | | Decrement variable VAR (a number) |
|- | |- | ||
| echo <any> | | echo <any> | ||
| Print out all arguments of echo | | Print out all arguments of echo | ||
|- | |- | ||
| − | | exit | + | | exit |
| Exit currently running script | | Exit currently running script | ||
|- | |- | ||
| Line 588: | Line 593: | ||
|- | |- | ||
| inc VAR | | inc VAR | ||
| − | | Increment variable VAR (a number) | + | | Increment variable VAR (a number) |
|- | |- | ||
| rem <any> | | rem <any> | ||
| Line 608: | Line 613: | ||
| Send FHT command. See [[FS20]] for details. | | Send FHT command. See [[FS20]] for details. | ||
|- | |- | ||
| − | | fs20 receive | + | | fs20 receive |
| Receive FS20/FHT sequence and display it. | | Receive FS20/FHT sequence and display it. | ||
|- | |- | ||
| Line 614: | Line 619: | ||
| Send FS20 command. See [[FS20]] for details. | | Send FS20 command. See [[FS20]] for details. | ||
|- | |- | ||
| − | | fs20 ws300 | + | | fs20 ws300 |
| Receive FS20 sequence from WS300 weather station and decode it. | | Receive FS20 sequence from WS300 weather station and decode it. | ||
|- | |- | ||
| Line 650: | Line 655: | ||
| Send a keypress to the menu | | Send a keypress to the menu | ||
|- | |- | ||
| − | | glcdmenu update | + | | glcdmenu update |
| Update the menu | | Update the menu | ||
|- | |- | ||
| Line 659: | Line 664: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | nmea get | + | | nmea get |
| Get latitude and longitude data | | Get latitude and longitude data | ||
|- | |- | ||
| − | | nmea satellites | + | | nmea satellites |
| Get satellites | | Get satellites | ||
|- | |- | ||
| Line 683: | Line 688: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | bmp085 apress | + | | bmp085 apress |
| Get absolute pressure in Pa | | Get absolute pressure in Pa | ||
|- | |- | ||
| Line 692: | Line 697: | ||
| Get pressure at N0, height in cm needed | | Get pressure at N0, height in cm needed | ||
|- | |- | ||
| − | | bmp085 temp | + | | bmp085 temp |
| − | | Get temperature in 0. | + | | Get temperature in 0.1°C |
|- | |- | ||
| ds1631 convert ADDR VALUE | | ds1631 convert ADDR VALUE | ||
| Line 701: | Line 706: | ||
| Read last converted temperature | | Read last converted temperature | ||
|- | |- | ||
| − | | ee dir | + | | ee dir |
| List files in I2C EEPROM. | | List files in I2C EEPROM. | ||
|- | |- | ||
| Line 707: | Line 712: | ||
| Remove file PATH. | | Remove file PATH. | ||
|- | |- | ||
| − | | i2c detect | + | | i2c detect |
| list detected I2C Chips | | list detected I2C Chips | ||
|- | |- | ||
| − | | i2c pca9555 in | + | | i2c pca9555 in |
| read word from register address on I2C chip | | read word from register address on I2C chip | ||
|- | |- | ||
| Line 762: | Line 767: | ||
|- | |- | ||
| mcp23017 clear pin ADDR PORT BIT | | mcp23017 clear pin ADDR PORT BIT | ||
| − | | Clear Port BIT for PORT A or B | + | | Clear Port BIT for PORT A or B |
|- | |- | ||
| mcp23017 get iodir ADDR PORT | | mcp23017 get iodir ADDR PORT | ||
| Line 771: | Line 776: | ||
|- | |- | ||
| mcp23017 get port ADDR PORT | | mcp23017 get port ADDR PORT | ||
| − | | Get Port Register (i.e. Port Pin State) for PORT A or B | + | | Get Port Register (i.e. Port Pin State) for PORT A or B |
|- | |- | ||
| mcp23017 getreg ADDR REGADDR | | mcp23017 getreg ADDR REGADDR | ||
| Line 786: | Line 791: | ||
|- | |- | ||
| mcp23017 set pin ADDR PORT BIT | | mcp23017 set pin ADDR PORT BIT | ||
| − | | Set Port BIT for PORT A or B | + | | Set Port BIT for PORT A or B |
|- | |- | ||
| mcp23017 setreg ADDR REGADDR VALUE | | mcp23017 setreg ADDR REGADDR VALUE | ||
| Line 792: | Line 797: | ||
|- | |- | ||
| mcp23017 toggle pin ADDR PORT BIT | | mcp23017 toggle pin ADDR PORT BIT | ||
| − | | Toggle Port BIT for PORT A or B | + | | Toggle Port BIT for PORT A or B |
|- | |- | ||
| pca9531 ADDR PERIODPWM1 DUTYPWM1 PERIODPWM2 DUTYPWM2 LED0..3 LED4..7 | | pca9531 ADDR PERIODPWM1 DUTYPWM1 PERIODPWM2 DUTYPWM2 LED0..3 LED4..7 | ||
| Line 806: | Line 811: | ||
| Get temperature | | Get temperature | ||
|- | |- | ||
| − | | tsl2550 lux | + | | tsl2550 lux |
| Show light level by reading adc registers and computing level | | Show light level by reading adc registers and computing level | ||
|- | |- | ||
| Line 851: | Line 856: | ||
| Calibrate to 1000 Ohm precision Resistor. | | Calibrate to 1000 Ohm precision Resistor. | ||
|- | |- | ||
| − | | kty cal get | + | | kty cal get |
| Return the calibration difference to 2k2 Resistor. | | Return the calibration difference to 2k2 Resistor. | ||
|- | |- | ||
| kty get [CHANNEL] | | kty get [CHANNEL] | ||
| − | | Get the temperature in xxx.x | + | | Get the temperature in xxx.x °C of CHANNEL or if no channel set of all channels. |
|- | |- | ||
|} | |} | ||
| Line 864: | Line 869: | ||
|- | |- | ||
| curtain VALUE | | curtain VALUE | ||
| − | | Set value of curtain. 0=closed..7=open. If you use fewer sensors, use the corrent value instead of 7. | + | | Set value of curtain. 0=closed..7=open. If you use fewer sensors, use the corrent value instead of 7. |
|- | |- | ||
| − | | curtainlast | + | | curtainlast |
| Return last known position | | Return last known position | ||
|- | |- | ||
| − | | curtainmax | + | | curtainmax |
| Return maximum position | | Return maximum position | ||
|- | |- | ||
| − | | curtainoff | + | | curtainoff |
| Switch motor off | | Switch motor off | ||
|- | |- | ||
| Line 884: | Line 889: | ||
| Read and display the status of pin NAME. | | Read and display the status of pin NAME. | ||
|- | |- | ||
| − | | pin list | + | | pin list |
| List all known named-pins. | | List all known named-pins. | ||
|- | |- | ||
| Line 917: | Line 922: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | rfm12 reinit | + | | rfm12 reinit |
| Re-initialize the RFM12 FSK module. | | Re-initialize the RFM12 FSK module. | ||
|- | |- | ||
| Line 944: | Line 949: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | rfm12 ask sense | + | | rfm12 ask sense |
| Trigger (Tevion) ASK sensing. Enable ext. filter pin before! | | Trigger (Tevion) ASK sensing. Enable ext. filter pin before! | ||
|- | |- | ||
| Line 956: | Line 961: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | fht send | + | | fht send |
| housecode addr command data | | housecode addr command data | ||
|- | |- | ||
| − | | fs20 receive | + | | fs20 receive |
| Receive FS20/FHT sequence and display it. | | Receive FS20/FHT sequence and display it. | ||
|- | |- | ||
| − | | fs20 send | + | | fs20 send |
| housecode addr command data | | housecode addr command data | ||
|- | |- | ||
| Line 974: | Line 979: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | sd dir | + | | sd dir |
| List contents of current SD directory. | | List contents of current SD directory. | ||
|- | |- | ||
| − | | sd info | + | | sd info |
| List information about SD card. | | List information about SD card. | ||
|- | |- | ||
| Line 996: | Line 1,001: | ||
|- | |- | ||
| sgc circle X Y RADIUS | | sgc circle X Y RADIUS | ||
| − | | Draw circle with parameters and colour specified in sgc_colour | + | | Draw circle with parameters and colour specified in sgc_colour |
|- | |- | ||
| − | | sgc cls | + | | sgc cls |
| Clear screen | | Clear screen | ||
|- | |- | ||
| Line 1,016: | Line 1,021: | ||
| Draw ASCII character in graphics format at specified position and size with colour specified in sgc_colour | | Draw ASCII character in graphics format at specified position and size with colour specified in sgc_colour | ||
|- | |- | ||
| − | | sgc getpwr | + | | sgc getpwr |
| Get Power Status | | Get Power Status | ||
|- | |- | ||
| Line 1,046: | Line 1,051: | ||
| Replace old colour - red-green-blue 0..0x1F or 2-byte RGB with only two parameters in selected area - with colour specified in sgc_colour | | Replace old colour - red-green-blue 0..0x1F or 2-byte RGB with only two parameters in selected area - with colour specified in sgc_colour | ||
|- | |- | ||
| − | | sgc result | + | | sgc result |
| Get result from last command | | Get result from last command | ||
|- | |- | ||
| Line 1,097: | Line 1,102: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | sht humid | + | | sht humid |
| Return humidity of SHT sensor | | Return humidity of SHT sensor | ||
|- | |- | ||
| − | | sht raw | + | | sht raw |
| Return raw hex temp (first line) and humidity value (second line) of SHT sensor | | Return raw hex temp (first line) and humidity value (second line) of SHT sensor | ||
|- | |- | ||
| − | | sht temp | + | | sht temp |
| Return temperature of SHT sensor | | Return temperature of SHT sensor | ||
|- | |- | ||
| Line 1,148: | Line 1,153: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | pwm stop | + | | pwm stop |
| Stop wav | | Stop wav | ||
|- | |- | ||
| Line 1,161: | Line 1,166: | ||
|- | |- | ||
| channel CHANNEL VALUE FUNCTION | | channel CHANNEL VALUE FUNCTION | ||
| − | | Get/Set stella channel to value. Second and third parameters are optional. Function: You may use 's' for instant set, 'f' for fade and 'y' for flashy fade. | + | | Get/Set stella channel to value. Second and third parameters are optional. Function: You may use 's' for instant set, 'f' for fade and 'y' for flashy fade. |
|- | |- | ||
| − | | channels | + | | channels |
| Return stella channel size | | Return stella channel size | ||
|- | |- | ||
| Line 1,169: | Line 1,174: | ||
| Get/Set stella fade step | | Get/Set stella fade step | ||
|- | |- | ||
| − | | stella load | + | | stella load |
| Load values from eeprom | | Load values from eeprom | ||
|- | |- | ||
| − | | stella store | + | | stella store |
| Store values in eeprom | | Store values in eeprom | ||
|- | |- | ||
| − | | tank get | + | | tank get |
| get last value | | get last value | ||
|- | |- | ||
| − | | tank param save | + | | tank param save |
| write tank parameter to EEPROM | | write tank parameter to EEPROM | ||
|- | |- | ||
| Line 1,184: | Line 1,189: | ||
| set tank parameter | | set tank parameter | ||
|- | |- | ||
| − | | tank param show | + | | tank param show |
| show tanklevel parameters | | show tanklevel parameters | ||
|- | |- | ||
| − | | tank start | + | | tank start |
| start measure | | start measure | ||
|- | |- | ||
| − | | tank zero | + | | tank zero |
| probe sensor zero offset | | probe sensor zero offset | ||
|- | |- | ||
| Line 1,232: | Line 1,237: | ||
| press power command | | press power command | ||
|- | |- | ||
| − | | lome6 reset | + | | lome6 reset |
| press reset command | | press reset command | ||
|- | |- | ||
| Line 1,238: | Line 1,243: | ||
| set temperature command | | set temperature command | ||
|- | |- | ||
| − | | lome6 state | + | | lome6 state |
| get state command | | get state command | ||
|- | |- | ||
| Line 1,250: | Line 1,255: | ||
| ''Short description'' | | ''Short description'' | ||
|- | |- | ||
| − | | alias list | + | | alias list |
| List all available aliases | | List all available aliases | ||
|- | |- | ||
| − | | artnet test | + | | artnet test |
| artnet test | | artnet test | ||
|- | |- | ||
| Line 1,262: | Line 1,267: | ||
| Dump the memory at ADDR (16 bytes). | | Dump the memory at ADDR (16 bytes). | ||
|- | |- | ||
| − | | eeprom reinit | + | | eeprom reinit |
| Force reinitialization of the EEPROM config area | | Force reinitialization of the EEPROM config area | ||
|- | |- | ||
| − | | ems stats | + | | ems stats |
| Report statistic counters | | Report statistic counters | ||
|- | |- | ||
| − | | free | + | | free |
| Display free space. | | Display free space. | ||
|- | |- | ||
| − | | help | + | | help |
| List which commands are available. | | List which commands are available. | ||
|- | |- | ||
| Line 1,277: | Line 1,282: | ||
| Send MESSAGE to compiled in httplog service | | Send MESSAGE to compiled in httplog service | ||
|- | |- | ||
| − | | ipstats | + | | ipstats |
| Display IP statistics. | | Display IP statistics. | ||
|- | |- | ||
| − | | mb recv | + | | mb recv |
| Receive data from modbus | | Receive data from modbus | ||
|- | |- | ||
| Line 1,289: | Line 1,294: | ||
| Save MESSAGE as new message of the day, otherwise just show current message | | Save MESSAGE as new message of the day, otherwise just show current message | ||
|- | |- | ||
| − | | msr1 get | + | | msr1 get |
| Get data | | Get data | ||
|- | |- | ||
| Line 1,295: | Line 1,300: | ||
| Send specified MySQL query to the configured server | | Send specified MySQL query to the configured server | ||
|- | |- | ||
| − | | ns | + | | ns |
| update net statistic for public anouncment of currently running ethersex | | update net statistic for public anouncment of currently running ethersex | ||
|- | |- | ||
| Line 1,310: | Line 1,315: | ||
| Send command to projector | | Send command to projector | ||
|- | |- | ||
| − | | sll get | + | | sll get |
| Request the logged data | | Request the logged data | ||
|- | |- | ||
| − | | sram memtest | + | | sram memtest |
| Perform a memory test | | Perform a memory test | ||
|- | |- | ||
| − | | srf05 | + | | srf05 |
| Read SRF05 measurement | | Read SRF05 measurement | ||
|- | |- | ||
| − | | to1 get | + | | to1 get |
| Request data from sensor | | Request data from sensor | ||
|- | |- | ||
| Line 1,325: | Line 1,330: | ||
| Send MESSAGE to compiled in twitter service | | Send MESSAGE to compiled in twitter service | ||
|- | |- | ||
| − | | upnp send | + | | upnp send |
| Manually send UPnP broadcast packet | | Manually send UPnP broadcast packet | ||
|- | |- | ||
| Line 1,331: | Line 1,336: | ||
| Set the USART baudrate to BAUD. | | Set the USART baudrate to BAUD. | ||
|- | |- | ||
| − | | version | + | | version |
| Display the version number. | | Display the version number. | ||
|- | |- | ||
| − | | weather | + | | weather |
| Get eltako weather data | | Get eltako weather data | ||
|- | |- | ||
| Line 1,340: | Line 1,345: | ||
| Send WAKE-ON-LAN command to MAC | | Send WAKE-ON-LAN command to MAC | ||
|- | |- | ||
| − | | yport stats | + | | yport stats |
| Report statistic counters | | Report statistic counters | ||
|- | |- | ||
| − | | zbus stats | + | | zbus stats |
| Report statistic counters | | Report statistic counters | ||
|- | |- | ||
Latest revision as of 21:34, 12 March 2018
This page is automatically generated from the files in the Ethersex source code repository. Do not edit this page but send patches for those files!
Bluetooth SPP Module (Bluetooth)
| Command syntax | Short description |
| bt cmd | send an AT command |
| bt stats | report statistics counter |
DNS Resolver
| Command syntax | Short description |
| dns server [IPADDR] | Display/Set the IP address of the DNS server to use to IPADDR. |
| nslookup HOSTNAME | Do DNS lookup for HOSTNAME (call twice). |
Digital/Analog Conversion (DAC)
| Command syntax | Short description |
| ltc1257_delay `[VALUE] | Set (if VALUE given) or get (no VALUE) delay for LTC1257 output bit changes in µs' |
| ltc1257_set `[VALUE0] [VALUE1] ... | Set output to value (value: 0-4095)' |
| tlc5620 `[CHANNEL] [VALUE] | Set Output to value (Value: 0-0xff)' |
Fnordlicht
| Command syntax | Short description |
| fnordlicht "ADDRESS RED | GREEN,BLUE",fnordlicht command to set RGB color |
| fnordlicht_init | fnordlicht init |
HD44780 LCD
| Command syntax | Short description |
| hr20 hourbar START STOP | Update hourbar to show ticks between START and STOP (range 0..23) |
| hr20 toggle SEG | Toggle segment SEG (a number, not a symbolic name!) |
| lcd backlight [STATE] | get or set the state of the lcd backlight |
| lcd char N D1 D2 D3 D4 D5 D6 D7 D8 | Define use-definable char N with data D1..D8 (provide DATA in hex) |
| lcd clear [LINE] | Clear line LINE (0..3) or the whole display (if parameter is omitted) |
| lcd goto LINE COL | Move cursor to LINE and column COL (origin is 0/0) |
| lcd print charset FROM TO | Print char FROM up to char TO |
| lcd reinit CURSOR BLINK | Reinitialize the display, set whether to show the cursor (CURSOR, 0 or 1) and whether the cursor shall BLINK |
| lcd shift DIR | Shift the display to DIR (either left or right) |
| lcd write TEXT | Write TEXT to the current cursor location |
Infrared Send/Receive (IRMP)
| Command syntax | Short description |
| irmp receive | receive an IR command |
| irmp send PROTOCOL DEVICE COMMAND REPEAT | send COMMAND with REPEAT flag to DEVICE using PROTOCOL |
Infrared Send/Receive (RC5)
| Command syntax | Short description |
| ir receive | receive an IR command |
| ir send DEVICE COMMAND | send COMMAND to DEVICE |
Miscellaneous
| Command syntax | Short description |
| periodic adjust OFFSET | Adjust periodic timers TOP value by adding OFFSET ticks. |
| periodic reset | Reset debug statistics for periodic module. |
| periodic stats | Print debug statistics for periodic module. |
NTP Client
| Command syntax | Short description |
| ntp query | Query the NTP server to get an NTP update. |
| ntp server [IPADDR] | Display/Set the IP address of the NTP server to use to IPADDR. |
| ntp status | Display NTP server status |
Network configuration
| Command syntax | Short description |
| enc dump | Dump the internal state of the enc to serial |
| gw [IP] | Display/Set the address of the default router. |
| ip [IP] | Display/Set the IP address. |
| mac [xx:xx:xx:xx:xx:xx] | Display/Set the MAC address. |
| netmask [IP] | Display/Set the network mask. |
Port I/O
| Command syntax | Short description |
| io get ddr PORTNUM | Display the current value of the DDR PORTNUM. |
| io get mask PORTNUM | Display the mask of the port PORTNUM. |
| io get pin PORTNUM | Display the current value of the PIN-register of the port PORTNUM. |
| io get port NUM | Display the current value of the PORT NUM. |
| io set ddr PORTNUM HEXVALUE [MASK] | Set the DDR of port PORTNUM to VALUE (possibly using the provided MASK). |
| io set port NUM HEXVALUE [MASK] | Set the PORT NUM to VALUE (possibly using the provided MASK). |
Reading and Writing EEPROM Space on Device
| Command syntax | Short description |
| eer eer <ADDR> <LENGTH> | Read n bytes from address after the config in eeprom. |
| eew eew <ADDR> <HEXBYTES> | Write Hexbytes at address after the config in epprom. |
| hostname | Display hostname. |
Resetting the controller
| Command syntax | Short description |
| bootloader | Call the bootloader. |
| reset | Reset the Ethersex. |
| wdreset | Go into endless loop to trigger a watchdog timeout. |
ADS
| Command syntax | Short description |
| ads get | Get the ADC value in hex. |
| ads mean [COUNT] | Get the mean of power of 2 COUNT ADC values in hex. |
| fuse | Display current fuse settings |
ASK
| Command syntax | Short description |
| ask 1527 HOUSECODE COMMAND DELAY CNT | |
| ask 2272 HOUSECODE COMMAND [DELAY] [CNT] [SYNC] | |
| ask fa20rf DEVICE [REPEAT] | |
| ask intertechno FAMILY GROUP DEVICE COMMAND | "Send Command to Intertechno switches (with coding wheel). FAMILY: A=1, ..." |
| ask itsl HOUSECODE COMMAND BUTTON [DIM] | "Send Command to Intertechno Self learning switches and dimmers. DIM works only with dimmers and values 0-15." |
| ask oase FAMILY GROUP DEVICE COMMAND | |
| ask tevion HOUSECODE COMMAND DELAY CNT |
Clock
| Command syntax | Short description |
| date | Print the current date. |
| lastdcf | Print when last valid DCF signal was received. |
| time [UNIXTIME] | Display/Set the current time in seconds since January 1st 1970. |
| uptime | Display ethersex uptime in unix format. |
| whm | Display ethersex uptime. |
Application_Sample
| Command syntax | Short description |
| sample | Manually call application sample commands |
| sample_init | Manually call application sample init method |
| sample_periodic | Manually call application sample periodic method |
BSBPORT commands
| Command syntax | Short description |
| bsbport get P1 P2 P3 P4 SRC TYPE | Show specific message currently in buffer format value as TYPE type is one of RAW STA TMP FP1 FP5 |
| bsbport list | List all messages currently in buffer output in RAW TMP FP1 FP5 |
| bsbport query P1 P2 P3 P4 [DEST] | Send Message to query for a value DEST is optional defaults to 0 |
| bsbport set P1 P2 P3 P4 DEST TYPE VALUE | Send Message to set value type is one of RAW SEL TMP FP1 FP5 |
| bsbport stats | Report statistic counters OK/CRC/Lenght under/Lenght over/Droped/Buffer/BufferNet/Retransmit |
MCUF
| Command syntax | Short description |
| mcuf modul N | Select module N |
| mcuf modul list | List all modules |
| mcuf showclock | Show digital clock |
| mcuf showstring MESSAGE | Show scrolling MESSAGE on the display |
CRC
| Command syntax | Short description |
| adc get [CHANNEL] | Get the ADC value in hex of CHANNEL or if no channel set of all channels. |
| adc vget [CHANNEL] | Get the ADC value in volt of CHANNEL or if no channel set of all channels. |
| adc vref [VOLTAGE] | Get/Set ADC reference voltage calibration. |
| crc calc | "read the ethersex program code and calc a crc16 of it" |
| crc read | "read out the crc16 value at the end of the program space" |
| hr20 temp | Read HR20 temperature sensor. |
CRON-Dienst
| Command syntax | Short description |
| cron add MIN HOUR DAY MONTH DOW ECMD | Add ECMD to cron to be executed at given time |
| cron anacron POSITION [STATE] | show/set job anacron state |
| cron list | Show all cron entries |
| cron persistent POSITION [STATE] | show/set job persistance state |
| cron rm [POSITION] | Remove one cron entry |
| cron save | Saves all persistent jobs |
| cron utc POSITION [STATE] | show/set utc state |
DALI
| Command syntax | Short description |
| dali cmd [TARGET] [COMMAND] [!][?] | "send the given command (decimal) to targets (all, g00 to g15, s00 to s63), auto repeat with !, read reply with ?" |
| dali dim [TARGET] [LEVEL] | "dim targets (all, g00 to g15, s00 to s63) to given level (0-254)" |
| dali raw [BYTE1] [BYTE2] | "send a raw frame (two bytes, given in hex) over the DALI bus" |
| dali scmd [SPECIAL COMMAND] [DATA] [!][?] | "send special command (256-287) with data, auto repeat with !, read reply with ?" |
DHT
| Command syntax | Short description |
| dht humid [SENSORNUMBER] | Return humidity of DHT sensor |
| dht list | Return a list of mapped sensor names |
| dht temp [SENSORNUMBER] | Return temperature of DHT sensor |
DMX_FXSlot commands
| Command syntax | Short description |
| dmx fxslot devices | set the device settings |
| dmx fxslot effect | set the effect settings |
| dmx fxslot reset | reset all fxslots and clear saved ones in EEPROM |
| dmx fxslot restore | restore the settings from EEPROM |
| dmx fxslot save | save the current fxslots to EEPROM |
DMX_Storage commands
| Command syntax | Short description |
| dmx channels | Get channels per universe |
| dmx get | Return channel value |
| dmx set | Set channel values |
| dmx universe | Get a whole universe |
| dmx universes | Get universes |
Dallas_1-wire_Bus
| Command syntax | Short description |
| 1w ds2450 convert [DEVICE] | `start conversion (with optional input mask and read out control)' |
| 1w ds2450 get [DEVICE] | `get conversion result (one or all channels)' |
| 1w ds2450 oc [DEVICE] | `get/set output control (per channel)' |
| 1w ds2450 oe [DEVICE] | `get/set output enable (per channel)' |
| 1w ds2450 por [DEVICE] | `get/set power on reset (per channel)' |
| 1w ds2450 power [DEVICE] | `get/set power supply of device (global)' |
| 1w ds2450 range [DEVICE] | `get/set input voltage range (per channel)' |
| 1w ds2450 res [DEVICE] | `get/set bit resolution of AD convert (per channel)' |
| 1w get DEVICE | Return temperature value of onewire device (provide 64-bit ID as 16-hex-digits) |
| 1w list | Return a list of the connected onewire devices |
| 1w name clear ID | Delete a name mapping |
| 1w name list | Return a list of mapped device names |
| 1w name save | Save name mappings to EEPROM |
| 1w name set ID DEVICE NAME | Assign a name to/from an device address |
DataFlash
| Command syntax | Short description |
| df status | Display internal status. |
| fs format | Format the filesystem. |
| fs inspect inode INODE | Inspect INODE (and associated page). |
| fs inspect node NODE | Inspect NODE and dump to serial. |
| fs list | List the directory. |
| fs mkfile NAME | Create a new file NAME. |
| fs remove NAME | Delete the file NAME. |
| fs truncate NAME LEN | Truncate the file NAME to LEN bytes. |
DC3840 mobil camera support
| Command syntax | Short description |
| dc3840 capture | Take a picture. Access 'dc3840' via VFS afterwards. See DC3840 Camera for details. |
| dc3840 light | Light level of camera |
| dc3840 send A B C D E | Send provided command bytes to the camera. |
| dc3840 sync | Re-sync to the camera |
| dc3840 zoom | Enable zoom of camera |
ECMDScript
| Command syntax | Short description |
| call FILENAME | Start script named FILENAME |
| cat FILENAME | cat file content (with debug only) |
| dec VAR | Decrement variable VAR (a number) |
| echo <any> | Print out all arguments of echo |
| exit | Exit currently running script |
| get VAR | Get value of variable VAR |
| goto N | Goto line N in currently running script |
| if ( CMD/VAR == CONST ) then CMD2 | If condition matches execute CMD2 |
| inc VAR | Increment variable VAR (a number) |
| rem <any> | Remark for anything |
| set VAR VALUE | Set variable VAR to VALUE |
| wait I | Wait I milliseconds |
FS20
| Command syntax | Short description |
| fht send HOUSECODE ADDR CMD [CMD2] | Send FHT command. See FS20 for details. |
| fs20 receive | Receive FS20/FHT sequence and display it. |
| fs20 send HOUSECODE ADDR CMD [CMD2] | Send FS20 command. See FS20 for details. |
| fs20 ws300 | Receive FS20 sequence from WS300 weather station and decode it. |
Frequency Counter
| Command syntax | Short description |
| fc %duty [CHANNEL] | "returns last on duty cycle in percent for given channel" |
| fc duty [CHANNEL] | "returns last on duty cycle (0-255) for given channel" |
| fc freq [CHANNEL] | "returns last frequency in Hz for given channel" |
| fc off [CHANNEL] | "switch off frequency counting on given channel" |
| fc on [CHANNEL] | "switch on frequency counting on given channel" |
| fc ticks [CHANNEL] | "returns last frequency in CPU ticks for given channel" |
GLCD_Menu
| Command syntax | Short description |
| glcdmenu key VALUE | Send a keypress to the menu |
| glcdmenu update | Update the menu |
GPS
| Command syntax | Short description |
| nmea get | Get latitude and longitude data |
| nmea satellites | Get satellites |
H-Bridge
| Command syntax | Short description |
| hbridge [action] [enable_l] [enable_r] | Set H-Bridge command |
| hbridge pwm int | Set H-Bridge enable line valueeg. speed |
I2C (TWI)
| Command syntax | Short description |
| bmp085 apress | Get absolute pressure in Pa |
| bmp085 height PRESSNN | Get height in cm, pressure at N0 needed |
| bmp085 pressnn HEIGHT | Get pressure at N0, height in cm needed |
| bmp085 temp | Get temperature in 0.1°C |
| ds1631 convert ADDR VALUE | Initiate temperature conversions (0: stop, 1: convert) |
| ds1631 temp ADDR | Read last converted temperature |
| ee dir | List files in I2C EEPROM. |
| ee rm PATH | Remove file PATH. |
| i2c detect | list detected I2C Chips |
| i2c pca9555 in | read word from register address on I2C chip |
| i2c pca9555 mode VALUE | select input or output mode for pins on I2C chip |
| i2c pca9555 out VALUE | write word to register address on I2C chip |
| i2c rbb ADDR | read byte from I2C chip |
| i2c rbd CHIPADDR REGADDR | read byte from register address at I2C chip |
| i2c rwd CHIPADDR REGADDR | read word from register address at I2C chip |
| i2c wbb ADDR HEXVALUE | write byte to I2C chip |
| i2c wbd CHIPADDR REGADDR HEXVALUE | write byte to register address on I2C chip |
| i2c wwd CHIPADDR REGADDR HEXVALUE | write word to register address on I2C chip |
| lm75 ADDR | Get temperature |
| max7311 getDDRw ADDR | Get Direction-Register DDR |
| max7311 getINw ADDR | Get Input-Register IN |
| max7311 getOUTw ADDR | Get Output-Register OUT |
| max7311 pulse ADDR BIT TIME | Toggle Output-BIT for TIME (in ms) |
| max7311 set ADDR BIT VALUE | Set Output-BIT to VALUE (bool) |
| max7311 setDDRw ADDR VALUE | Set Direction-Register DDR (VALUE as hex) |
| max7311 setOUTw ADDR VALUE | Set Output-Register OUT (VALUE as hex) |
| mcp23017 clear pin ADDR PORT BIT | Clear Port BIT for PORT A or B |
| mcp23017 get iodir ADDR PORT | Get I/O Direction Register for PORT A or B |
| mcp23017 get olat ADDR PORT | Get Output Latch Register for PORT A or B |
| mcp23017 get port ADDR PORT | Get Port Register (i.e. Port Pin State) for PORT A or B |
| mcp23017 getreg ADDR REGADDR | Get Register REGADDR |
| mcp23017 pulse pin ADDR PORT BIT TIME | Toggle-Pulse Port BIT for PORT A or B for TIME ms |
| mcp23017 set iodir ADDR PORT VALUE | Set I/O Direction Register for PORT A or B (VALUE as hex) |
| mcp23017 set olat ADDR PORT VALUE | Set Output Latch Register for PORT A or B (VALUE as hex) |
| mcp23017 set pin ADDR PORT BIT | Set Port BIT for PORT A or B |
| mcp23017 setreg ADDR REGADDR VALUE | Set Register REGADDR (VALUE as hex) |
| mcp23017 toggle pin ADDR PORT BIT | Toggle Port BIT for PORT A or B |
| pca9531 ADDR PERIODPWM1 DUTYPWM1 PERIODPWM2 DUTYPWM2 LED0..3 LED4..7 | set PWM1 and PWM2 and LED states |
| pcf8574x read ADDR CHIP | Get bits |
| pcf8574x set ADDR CHIP HEXVALUE | Set bits |
| tmp175 ADDR | Get temperature |
| tsl2550 lux | Show light level by reading adc registers and computing level |
| tsl2550 mode VALUE | Set the TSL2550s operating mode (0: standard range, 1: extended range) |
| tsl2550 power VALUE | Set the TSL2550s power state (0: down, 1:up) |
| tsl2561 lux DEVNUM | Get LUX value |
| tsl2561 raw DEVNUM | Get RAW channel values |
| tsl2561 setmode DEVNUM TIME GAIN PACKAGE | Set device mode |
Jabber
| Command syntax | Short description |
| jabber_host [HOSTNAME] | JABBER hostname |
| jabber_pass [PASSWORD] | JABBER password |
| jabber_resrc [RESOURCE] | JABBER resource |
| jabber_user [USERNAME] | JABBER username |
KTY
| Command syntax | Short description |
| kty autocalibrate CHANNEL | Calibrate to 1000 Ohm precision Resistor. |
| kty cal get | Return the calibration difference to 2k2 Resistor. |
| kty get [CHANNEL] | Get the temperature in xxx.x °C of CHANNEL or if no channel set of all channels. |
MotorCurtain commands
| Command syntax | Short description |
| curtain VALUE | Set value of curtain. 0=closed..7=open. If you use fewer sensors, use the corrent value instead of 7. |
| curtainlast | Return last known position |
| curtainmax | Return maximum position |
| curtainoff | Switch motor off |
Named_PIN
| Command syntax | Short description |
| pin get NAME | Read and display the status of pin NAME. |
| pin list | List all known named-pins. |
| pin set NAME STATUS | Set the status of pin NAME to STATUS. |
| pin toggle NAME | Toggle the status of pin NAME. |
PWM
| Command syntax | Short description |
| dtmf CHARS | send CHARS as DTMF |
| freq set FREQUENCY DELAY | Set frequency for DELAY ms |
| pwm fade [channel +-diff startvalue] | Set fading at channel with startvalue and change each stepp to diff (must be signed 3 digit) |
| pwm set [channel value] | Set channel to value |
RFM12
| Command syntax | Short description |
| rfm12 reinit | Re-initialize the RFM12 FSK module. |
| rfm12 setbandwidth MODULE BW | Set receiver bandwidth of MODULE to BW. |
| rfm12 setbaud MODULE BAUD | Set baudrate of MODULE to BAUD. |
| rfm12 setdrssi MODULE DRSSI | Set the drssi of MODULE to DRSSI. |
| rfm12 setgain MODULE GAIN | Set preamplifier gain of MODULE to GAIN. |
| rfm12 setmod MOD | Set modulation of the RFM12 FSK module to MOD. |
| rfm12 status MODULE | Display internal status of MODULE. |
RFM12_ASK
| Command syntax | Short description |
| rfm12 ask sense | Trigger (Tevion) ASK sensing. Enable ext. filter pin before! |
| rfm12 external filter [1] | Enable ext. filter pin if argument is present (disable otherwise) |
RFM12_FS20
| Command syntax | Short description |
| fht send | housecode addr command data |
| fs20 receive | Receive FS20/FHT sequence and display it. |
| fs20 send | housecode addr command data |
| fs20 setdebug DEBUG | Set debug to DEBUG. |
SD-Karte
| Command syntax | Short description |
| sd dir | List contents of current SD directory. |
| sd info | List information about SD card. |
| sd mkdir PATH | Create directory hierarchy PATH. |
| sd rm PATH | Remove file PATH. |
SGC commands
| Command syntax | Short description |
| sgc adduc ADDR CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 | Add user character: address 0..0x1F and 8 bytes character |
| sgc circle X Y RADIUS | Draw circle with parameters and colour specified in sgc_colour |
| sgc cls | Clear screen |
| sgc colour RED GREEN BLUE | Set pen / font colour:red-green-blue 0..0x1F or 2-byte RGB with only two parameters |
| sgc contrast CONTRAST | Set contrast value 0..0x0F |
| sgc druc ADDR X Y | Draw user character saved from sgc_adduc at address 0..0x1F and with colour specified in sgc_colour |
| sgc font FONT PROPORTIONAL | Set font type:0..2 and 0:not proportional 1:proportional |
| sgc gchar X Y WIDTH HEIGHT CHAR | Draw ASCII character in graphics format at specified position and size with colour specified in sgc_colour |
| sgc getpwr | Get Power Status |
| sgc line X1 Y1 X2 Y2 | Draw line between specified points with colour specified in sgc_colour |
| sgc object UMSB ULSB LMSB LLSB | Display object from SD card at specified address |
| sgc onoff ONOFF | Turn display on:1 or off:0 |
| sgc opacity OPACITY | Set text opacity 0:transparent 1:opaque |
| sgc pensize PENSIZE | Set pen size 0:solid 1:lines |
| sgc pixel X Y | Draw pixel at specified point with colour specified in sgc_colour |
| sgc rectangle X1 Y1 X2 Y2 | Draw rectangle with specified edges and with colour specified in sgc_colour |
| sgc repbgc RED GREEN BLUE | Replace background colour:red-green-blue 0..0x1F or 2-byte RGB with only two parameters |
| sgc repcol X_START Y_START X_END Y_END OLD_RED OLD_GREEN OLD_BLUE | Replace old colour - red-green-blue 0..0x1F or 2-byte RGB with only two parameters in selected area - with colour specified in sgc_colour |
| sgc result | Get result from last command |
| sgc scrcp SRC_X SRC_Y DST_X DST_Y WIDTH HEIGHT | Copy-Paste selected screen area |
| sgc script UMSB ULSB LMSB LLSB | Run 4DSL script from SD card at specified address |
| sgc sdicon X Y WIDTH HEIGHT SECTOR0 SECTOR1 SECTOR2 | Display icon from SD card at specified position and size stored at specified SD card sector |
| sgc setbgc RED GREEN BLUE | Set background colour:red-green-blue 0..0x1F or 2-byte RGB with only two parameters |
| sgc setip IPADDR | Change response IP address - volatile |
| sgc setpwr PWR | Set Power Status: 1:on 0:off |
| sgc setsleep AUTO MODE | Set Auto Shutdown Sleep 1:on 0:off / Set wakeup mode 0:Serial 1: Joystick |
| sgc settimeout TIMEOUT | Change auto-off idle time - volatile |
| sgc sleep SLEEP | Sleep mode 0:turn off SD 1:wake on serial 2:wake on joystick |
| sgc stg X Y WIDTH HEIGHT STRING | Draw ASCII string in graphics format at specified position and size with colour specified in sgc_colour) |
| sgc stt COL ROW STRING | Draw ASCII string in text format at specified col and row and with colour specified in sgc_colour |
| sgc tchar COL ROW CHAR | Draw ASCII character in text format at specified col and row and with colour specified in sgc_colour |
| sgc triangle X1 Y1 X2 Y2 X3 Y3 | Draw triangle with edges counter-clockwise and with colour specified in sgc_colour |
| sgc video X Y WIDTH HEIGHT DELAY NUM_FRAMES0 NUM_FRAMES1 SECTOR0 SECTOR1 SECTOR2 | Display video / animation from SD card at specified position and size and with specified inter-frame delay and frame number stored at specified SD card sector |
SHT
| Command syntax | Short description |
| sht humid | Return humidity of SHT sensor |
| sht raw | Return raw hex temp (first line) and humidity value (second line) of SHT sensor |
| sht temp | Return temperature of SHT sensor |
SMS77
| Command syntax | Short description |
| sms77 MESSAGE | Send MESSAGE to compiled in sms77 service |
| sms77_pass [PASSWORD] | SMS77 password |
| sms77_recv [RECEIVER] | SMS receiver |
| sms77_type [TYPE] | SMS type |
| sms77_user [USERNAME] | SMS77 username |
PWM Servo Control
| Command syntax | Short description |
| pwm servo_dec SERVONR | Decrement position of servo SERVONR |
| pwm servo_inc SERVONR | Increment position of servo SERVONR |
| pwm servo_set SERVONR POSITION | Set servo with SERVONR to POSITION |
Sound/WAV support
| Command syntax | Short description |
| pwm stop | Stop wav |
| pwm wav <FILENAME> | Play wave file. Use VFS if compiled in. More details at Sound |
Stella_Light commands
| Command syntax | Short description |
| channel CHANNEL VALUE FUNCTION | Get/Set stella channel to value. Second and third parameters are optional. Function: You may use 's' for instant set, 'f' for fade and 'y' for flashy fade. |
| channels | Return stella channel size |
| fadestep FADESTEP | Get/Set stella fade step |
| stella load | Load values from eeprom |
| stella store | Store values in eeprom |
| tank get | get last value |
| tank param save | write tank parameter to EEPROM |
| tank param set PARAM VALUE | set tank parameter |
| tank param show | show tanklevel parameters |
| tank start | start measure |
| tank zero | probe sensor zero offset |
USB
| Command syntax | Short description |
| keyboard MESSAGE | Send MESSAGE as HID keyboard |
| mouse BUTTON DELTAX DELTAY | Send data as HID mouse |
ZACwire
| Command syntax | Short description |
| zac 306 PORT BIT | Return temperature of TSic 306 at BIT of PORT |
| zac 506 PORT BIT | Return temperature of TSic 506 at BIT of PORT |
| zac raw PORT BIT | Return raw hex temperature value of zacwire at BIT of PORT |
lome6
| Command syntax | Short description |
| lome6 get_t TYPE | get temperature command |
| lome6 power TYPE | press power command |
| lome6 reset | press reset command |
| lome6 set_t TYPE TEMPERATURE | set temperature command |
| lome6 state | get state command |
| lome6 uptime UPTIME | set/get uptime command |
Miscelleanous
| Command syntax | Short description |
| alias list | List all available aliases |
| artnet test | artnet test |
| cw send MESSAGE | Send MESSAGE in Morce Code |
| d ADDR | Dump the memory at ADDR (16 bytes). |
| eeprom reinit | Force reinitialization of the EEPROM config area |
| ems stats | Report statistic counters |
| free | Display free space. |
| help | List which commands are available. |
| ht MESSAGE | Send MESSAGE to compiled in httplog service |
| ipstats | Display IP statistics. |
| mb recv | Receive data from modbus |
| moodlight CHANNEL ONOFF | Set CHANNEL moodlight on=1 or off=0. If no channel is given return on if channel CHANNEL is moodlighted |
| motd [MESSAGE] | Save MESSAGE as new message of the day, otherwise just show current message |
| msr1 get | Get data |
| mysql query QUERY | Send specified MySQL query to the configured server |
| ns | update net statistic for public anouncment of currently running ethersex |
| pam USER PASSWORD | Use pam for user and password |
| push NUMBER | Push button identified by NUMBER |
| pwm melody [NUMBER] | Play melody |
| sanyoz700 CMD | Send command to projector |
| sll get | Request the logged data |
| sram memtest | Perform a memory test |
| srf05 | Read SRF05 measurement |
| to1 get | Request data from sensor |
| tw MESSAGE | Send MESSAGE to compiled in twitter service |
| upnp send | Manually send UPnP broadcast packet |
| usart baud BAUD | Set the USART baudrate to BAUD. |
| version | Display the version number. |
| weather | Get eltako weather data |
| wol MAC | Send WAKE-ON-LAN command to MAC |
| yport stats | Report statistic counters |
| zbus stats | Report statistic counters |
